Kingpin shims needed
- NMAD
- Senior Member
- Posts: 267
- Joined: 11 Mar 2015 15:07
- Full Name: noel
- Nickname: happy
- Home Town: C
- Current 4x4: 20
- Home Language: E
- Has thanked: 51 times
- Been thanked: 10 times
Re: Kingpin shims needed
Called around and finally got some .25mm shim plate for free as it was an offcut. It is brass so hope it's alright to use, the company that gave it said it will be fine to use so holding thumbs.
I never knew it would be so hard to cut it into the correct shape though, took about 15 min per shim
I never knew it would be so hard to cut it into the correct shape though, took about 15 min per shim
- Attachments
-
- image.jpg (1.23 MiB) Viewed 2876 times
- ricster
- Patrolman 1000+
- Posts: 5850
- Joined: 13 Jan 2010 11:16
- Full Name: Cedric Warner
- Nickname: Cedric
- Home Town: Alberton Gauteng
- Current 4x4: '99 Nissan Patrol 4.2 Turbo Diesel
- Home Language: English
- Location: LA..... No not Los Angles ..... Lower Alberton, Gauteng
- Has thanked: 591 times
- Been thanked: 468 times
Re: Kingpin shims needed
haha.... yip cutting the shim stock is not the easiest, but 15 mins is a good time though.....
Brass will be 100%, you could use stainless steel too. just add one shim, tighten everything up and see how much Nm it takes to start moving the hub left to right. Then add another if needed.
Brass will be 100%, you could use stainless steel too. just add one shim, tighten everything up and see how much Nm it takes to start moving the hub left to right. Then add another if needed.
Regards
Cedric
Nissan Patrol GL 4.2 Diesel Turbo (Iron Maiden)
Nissan SANI 3.0 V6 4x4 (SOLD)
Isuzu KB 280 DT 2x4 ('ol Smokey) - SOLD
Suzuki TL 1000R "V twin" (Growler) - SOLD
Cedric
Nissan Patrol GL 4.2 Diesel Turbo (Iron Maiden)
Nissan SANI 3.0 V6 4x4 (SOLD)
Isuzu KB 280 DT 2x4 ('ol Smokey) - SOLD
Suzuki TL 1000R "V twin" (Growler) - SOLD
- davidvdm
- Patrolman
- Posts: 629
- Joined: 13 Sep 2011 15:47
- Full Name: David vd Merwe
- Nickname: David - Hillbilly
- Home Town: West Coast
- Current 4x4: 1997 2.7TD Nissan Sani Mk3 4x4 SFA (SAFANI)
- Home Language: English/Afrikaans
- Has thanked: 4 times
- Been thanked: 48 times
- Contact:
Re: Kingpin shims needed
Cedric, help me out here... I thought that by adding shims you are going to be lifting the bearing out of its seat and thus it should all loosen up. By removing the shims it tightens things up and removes play.
I removed the shims on the Sani as I had wobble wheel syndrome and it all got fixed.
I removed the shims on the Sani as I had wobble wheel syndrome and it all got fixed.
David - Bfreesani
1997 Nissan Sani MK3 2.7TD - Hillbilly (SAFANI)
MQ C200 SFA
MQ H260 LSD Rear
MQ Transfer as second low range
5" Lift
33"x12.5x15" tires on 8.5J rims - Want 35's
DIY rock sliders
DIY Snorkel
Madman EMS
1997 Nissan Sani MK3 2.7TD - Hillbilly (SAFANI)
MQ C200 SFA
MQ H260 LSD Rear
MQ Transfer as second low range
5" Lift
33"x12.5x15" tires on 8.5J rims - Want 35's
DIY rock sliders
DIY Snorkel
Madman EMS
- Marino4x4
- Patrolman
- Posts: 520
- Joined: 19 Oct 2011 12:15
- Full Name: Marinus Potgieter
- Nickname: Marino4x4
- Home Town: Bloemfontein
- Current 4x4: Nissan Patrol
- Home Language: Afrikaans
- Location: Bloemfontein
- Has thanked: 17 times
- Been thanked: 84 times
Re: Kingpin shims needed
Hi David
As I have it he had a 0.5 shim in and replaced it with a 0.25 shim. He did not want to remove it completely.
As I have it he had a 0.5 shim in and replaced it with a 0.25 shim. He did not want to remove it completely.
- ricster
- Patrolman 1000+
- Posts: 5850
- Joined: 13 Jan 2010 11:16
- Full Name: Cedric Warner
- Nickname: Cedric
- Home Town: Alberton Gauteng
- Current 4x4: '99 Nissan Patrol 4.2 Turbo Diesel
- Home Language: English
- Location: LA..... No not Los Angles ..... Lower Alberton, Gauteng
- Has thanked: 591 times
- Been thanked: 468 times
Re: Kingpin shims needed
yeah... If removing all the shims, then the pressure on the bearings may be slightly too much ( depending on wear on the old bearings ) so only add a shim to get the correct setting of the bearing. mine were worn badly enough to allow me to run without any shims. I have kept the shims though as when I replace the bearings I will have to refit the shims.
Regards
Cedric
Nissan Patrol GL 4.2 Diesel Turbo (Iron Maiden)
Nissan SANI 3.0 V6 4x4 (SOLD)
Isuzu KB 280 DT 2x4 ('ol Smokey) - SOLD
Suzuki TL 1000R "V twin" (Growler) - SOLD
Cedric
Nissan Patrol GL 4.2 Diesel Turbo (Iron Maiden)
Nissan SANI 3.0 V6 4x4 (SOLD)
Isuzu KB 280 DT 2x4 ('ol Smokey) - SOLD
Suzuki TL 1000R "V twin" (Growler) - SOLD
- davidvdm
- Patrolman
- Posts: 629
- Joined: 13 Sep 2011 15:47
- Full Name: David vd Merwe
- Nickname: David - Hillbilly
- Home Town: West Coast
- Current 4x4: 1997 2.7TD Nissan Sani Mk3 4x4 SFA (SAFANI)
- Home Language: English/Afrikaans
- Has thanked: 4 times
- Been thanked: 48 times
- Contact:
Re: Kingpin shims needed
NMAD is adding shims, but I thought he's problem was that he has sloppy front end.
David - Bfreesani
1997 Nissan Sani MK3 2.7TD - Hillbilly (SAFANI)
MQ C200 SFA
MQ H260 LSD Rear
MQ Transfer as second low range
5" Lift
33"x12.5x15" tires on 8.5J rims - Want 35's
DIY rock sliders
DIY Snorkel
Madman EMS
1997 Nissan Sani MK3 2.7TD - Hillbilly (SAFANI)
MQ C200 SFA
MQ H260 LSD Rear
MQ Transfer as second low range
5" Lift
33"x12.5x15" tires on 8.5J rims - Want 35's
DIY rock sliders
DIY Snorkel
Madman EMS
- davidvdm
- Patrolman
- Posts: 629
- Joined: 13 Sep 2011 15:47
- Full Name: David vd Merwe
- Nickname: David - Hillbilly
- Home Town: West Coast
- Current 4x4: 1997 2.7TD Nissan Sani Mk3 4x4 SFA (SAFANI)
- Home Language: English/Afrikaans
- Has thanked: 4 times
- Been thanked: 48 times
- Contact:
Re: Kingpin shims needed
This is the kit I would to purchase..
http://www.roadrunneroffroad.com.au/Swi ... trol-.html
http://www.roadrunneroffroad.com.au/Swi ... trol-.html
David - Bfreesani
1997 Nissan Sani MK3 2.7TD - Hillbilly (SAFANI)
MQ C200 SFA
MQ H260 LSD Rear
MQ Transfer as second low range
5" Lift
33"x12.5x15" tires on 8.5J rims - Want 35's
DIY rock sliders
DIY Snorkel
Madman EMS
1997 Nissan Sani MK3 2.7TD - Hillbilly (SAFANI)
MQ C200 SFA
MQ H260 LSD Rear
MQ Transfer as second low range
5" Lift
33"x12.5x15" tires on 8.5J rims - Want 35's
DIY rock sliders
DIY Snorkel
Madman EMS
- NMAD
- Senior Member
- Posts: 267
- Joined: 11 Mar 2015 15:07
- Full Name: noel
- Nickname: happy
- Home Town: C
- Current 4x4: 20
- Home Language: E
- Has thanked: 51 times
- Been thanked: 10 times
Re: Kingpin shims needed
I removed the stock .05mm shim and replaced it with the 0.25mm shim to stiffen the steering up. Its noticeably stiffer than what it was and the wobble is better but its not perfect. May need to put another shim in of about .1m to loosen it up a bit. I think my wobble has more to do with my front wheel bearings as they had some up down play when I shaked the wheel on the jack stand. Got outer bearings and will replace once I get the inner bearings and seals from the agents and report back.
- ricster
- Patrolman 1000+
- Posts: 5850
- Joined: 13 Jan 2010 11:16
- Full Name: Cedric Warner
- Nickname: Cedric
- Home Town: Alberton Gauteng
- Current 4x4: '99 Nissan Patrol 4.2 Turbo Diesel
- Home Language: English
- Location: LA..... No not Los Angles ..... Lower Alberton, Gauteng
- Has thanked: 591 times
- Been thanked: 468 times
Re: Kingpin shims needed
Just for interest sakes, try with no shims in and see if that sorts the problem out. The up down movement may still be play in the king pins. Also check the wheel bearing nut and tighten ( to the correct torque !!!! ) then take for a drive and see. Maybe the wheel bearings are still good....
Regards
Cedric
Nissan Patrol GL 4.2 Diesel Turbo (Iron Maiden)
Nissan SANI 3.0 V6 4x4 (SOLD)
Isuzu KB 280 DT 2x4 ('ol Smokey) - SOLD
Suzuki TL 1000R "V twin" (Growler) - SOLD
Cedric
Nissan Patrol GL 4.2 Diesel Turbo (Iron Maiden)
Nissan SANI 3.0 V6 4x4 (SOLD)
Isuzu KB 280 DT 2x4 ('ol Smokey) - SOLD
Suzuki TL 1000R "V twin" (Growler) - SOLD
- Tinus lotz
- Moderator
- Posts: 7579
- Joined: 29 Aug 2010 13:07
- Full Name: Tinus lotz
- Nickname: Tinus lotz
- Home Town: Centurion
- Current 4x4: Nissan patrol 4.8 GRX 2005
Toyota 2.7 legend 35 LWB 4X4 - Home Language: Afrikaans
- Has thanked: 800 times
- Been thanked: 549 times
Re: Kingpin shims needed
Jip your patrol is a bit new for those bearings or can you see damage or water problems?NMAD wrote:I removed the stock .05mm shim and replaced it with the 0.25mm shim to stiffen the steering up. Its noticeably stiffer than what it was and the wobble is better but its not perfect. May need to put another shim in of about .1m to loosen it up a bit. I think my wobble has more to do with my front wheel bearings as they had some up down play when I shaked the wheel on the jack stand. Got outer bearings and will replace once I get the inner bearings and seals from the agents and report back.
Who is online
Users browsing this forum: No registered users and 44 guests