DIY DRAWER SYSTEM
- Rhett
- Senior Member
- Posts: 482
- Joined: 26 Jan 2016 14:48
- Full Name: Rhett van der Stelt
- Nickname: Rhett
- Home Town: Heidelberg
- Current 4x4: 3.2Did Shorty Pajero
- Home Language: English
- Location: Heidelberg
- Has thanked: 163 times
- Been thanked: 75 times
DIY DRAWER SYSTEM
I had been planning a drawer system for ages, and for our 3 week December haul, I thought I better get off my g@t and start something. Originally wanted everything in aluminum, but had to change plans halfway through. Frame was made up of mild steel 25mm² tube, and the sheeting I used was 3mm aluminium composite.
You can see the toolbox which was installed, and I wasn't sure if I wanted to remove it or work around it. Finally decided to keep it as it also houses the secondary AGM battery.
First welded up a base frame which everything will fit upon and which I could bolt into the existing brackets.
The drawers I made up from aluminium composite, riveted onto 25mm aluminium angle. I contemplated screwing / bolting everything together, but went with rivets. If Defenders are still together after 60 years, the drawers should last 6 years at least
I did screw the sliders on to the drawer though, as I was worried the movement and weight could shear off the rivets. The aluminium drawer using the composite as carcass is super light and very rigid.
I also contemplated powder-coating the steel, but went for Hammerite instead, mainly because of time constraints. I also cut out a template of the floor and laid a panel of 3mm ABS on top of the carpet so I wouldn't damage it.
Next step was to weld up and put together the top shelf. This was a tricky one as there was no way we could install it via the rear stable doors, but I wanted all that space... A rare photo of my trusty helper, aka wifey.
Top shelf fixed in, in hindsight I should have used bolts or self-tappers to fix it in place. The rivets would have to be drilled out if/when I take the system out.
I know some have hesitations against the Connect-It's, but I have used them many times and the new generation ones are almost unbreakable.
The Waeco we use is a 40l freezer and sadly I have never found a suitable cover for it, so SWAMBO made this super-duty cover, made from polyurethane / foil insulation, and fitted into denim sleeves, but that's another story!
Ps.. anyone who needs insulation can help themselves to the room-full I have!
The frame height and storage areas on each side of the contraption were designed to house our camping chairs (right) and solar panel (left), which are usually the first things to come out after the beers.
The bottom drawer we designed to fit two tin cans on top of each other. I used to use ammo boxes and hated the design. Top drawer will hold other things.
The second row of seats come out (no kidlets) so our thermocooler, and other nonsense we all like to take with, go there. The toolbox gives quick access to the recovery kit.
There is still another drawer which is almost done, to be installed next week. I tested the design by sitting on the fridge tray, so I'm pretty happy with the end result. I might tweak and add if needed in the future.
You can see the toolbox which was installed, and I wasn't sure if I wanted to remove it or work around it. Finally decided to keep it as it also houses the secondary AGM battery.
First welded up a base frame which everything will fit upon and which I could bolt into the existing brackets.
The drawers I made up from aluminium composite, riveted onto 25mm aluminium angle. I contemplated screwing / bolting everything together, but went with rivets. If Defenders are still together after 60 years, the drawers should last 6 years at least
I did screw the sliders on to the drawer though, as I was worried the movement and weight could shear off the rivets. The aluminium drawer using the composite as carcass is super light and very rigid.
I also contemplated powder-coating the steel, but went for Hammerite instead, mainly because of time constraints. I also cut out a template of the floor and laid a panel of 3mm ABS on top of the carpet so I wouldn't damage it.
Next step was to weld up and put together the top shelf. This was a tricky one as there was no way we could install it via the rear stable doors, but I wanted all that space... A rare photo of my trusty helper, aka wifey.
Top shelf fixed in, in hindsight I should have used bolts or self-tappers to fix it in place. The rivets would have to be drilled out if/when I take the system out.
I know some have hesitations against the Connect-It's, but I have used them many times and the new generation ones are almost unbreakable.
The Waeco we use is a 40l freezer and sadly I have never found a suitable cover for it, so SWAMBO made this super-duty cover, made from polyurethane / foil insulation, and fitted into denim sleeves, but that's another story!
Ps.. anyone who needs insulation can help themselves to the room-full I have!
The frame height and storage areas on each side of the contraption were designed to house our camping chairs (right) and solar panel (left), which are usually the first things to come out after the beers.
The bottom drawer we designed to fit two tin cans on top of each other. I used to use ammo boxes and hated the design. Top drawer will hold other things.
The second row of seats come out (no kidlets) so our thermocooler, and other nonsense we all like to take with, go there. The toolbox gives quick access to the recovery kit.
There is still another drawer which is almost done, to be installed next week. I tested the design by sitting on the fridge tray, so I'm pretty happy with the end result. I might tweak and add if needed in the future.
Rhett
https://www.youtube.com/channel/UC9e98c ... XUyixKJavQ
Nissan Patrol 4.8 GRX
Toyota Land Cruiser HJ45
https://www.youtube.com/channel/UC9e98c ... XUyixKJavQ
Nissan Patrol 4.8 GRX
Toyota Land Cruiser HJ45
- Tinus lotz
- Moderator
- Posts: 7579
- Joined: 29 Aug 2010 13:07
- Full Name: Tinus lotz
- Nickname: Tinus lotz
- Home Town: Centurion
- Current 4x4: Nissan patrol 4.8 GRX 2005
Toyota 2.7 legend 35 LWB 4X4 - Home Language: Afrikaans
- Has thanked: 800 times
- Been thanked: 549 times
- offroadbiker
- Moderator
- Posts: 2842
- Joined: 25 Jul 2012 08:36
- Full Name: Dirk de Clerk
- Nickname: ORB
- Home Town: Krugersdorp
- Current 4x4: Patrol GQ 4.2 ST
- Home Language: Afrikaans/English
- Location: Krugersdorp
- Has thanked: 186 times
- Been thanked: 262 times
- Herrie
- Patrolman 1000+
- Posts: 2999
- Joined: 08 Apr 2009 07:17
- Full Name: Kobus Pienaar
- Nickname: Herrie
- Home Town: Kempton Park
- Current 4x4: 1999 Patrol 4500e GRX
1983 Datsun Safari - Home Language: Afrikaans
- Location: Kempton Park
- Has thanked: 55 times
- Been thanked: 93 times
Re: DIY DRAWER SYSTEM
Ek het 'n klomp aircraft floor panels wat gebruik kan word vir dit want dit is baie lig en sterk en is regtig nie swaar nie!
- Attachments
-
- Floor Panels.jpg (427.02 KiB) Viewed 14846 times
Herrie op Safari/Patrollie
1983 Safari
1999 Patrol 4500 GRX
1983 Safari
1999 Patrol 4500 GRX
- Dustin
- Senior Member
- Posts: 428
- Joined: 14 Sep 2009 12:14
- Full Name: Dustin Roberts
- Nickname: Dustin
- Home Town: Port Elizabeth
- Current 4x4: Patrol-less :-(
- Home Language: English
- Location: Port Elizabeth
- Has thanked: 42 times
- Been thanked: 52 times
Re: DIY DRAWER SYSTEM
Nice work Rhett
a.k.a. Datsun Dustin
View my Patrol's story here : http://patrol4x4.co.za/viewtopic.php?f=43&t=6478
No hill too steep, no donga too deep !
GO PATROL !!!
View my Patrol's story here : http://patrol4x4.co.za/viewtopic.php?f=43&t=6478
No hill too steep, no donga too deep !
GO PATROL !!!
- Jorrie
- Patrolman 1000+
- Posts: 2184
- Joined: 21 Jun 2011 18:55
- Full Name: Jacobus Jordaan
- Nickname: Jorrie
- Home Town: Pretoria
- Current 4x4: 1998 Nissan Patrol 4500 GRX (now in Benji's hands), 2019 Zook Gen 4, 2011 4.8 GRX Patrol Adventure 60
- Home Language: English/Afrikaans
- Location: Pretoria
- Has thanked: 184 times
- Been thanked: 165 times
Re: DIY DRAWER SYSTEM
Looks good Rhett. Will have a look on Sunday!
Jorrie
1998 4500 GRX (Benji)
2011 4800 GRX Adventure 60 (Jorrie)
2011 Jimny Sold (Benji)
2 x 2019 Jimnies (1 x Lizzybean69, 1 x Jorrie)
1998 4500 GRX (Benji)
2011 4800 GRX Adventure 60 (Jorrie)
2011 Jimny Sold (Benji)
2 x 2019 Jimnies (1 x Lizzybean69, 1 x Jorrie)
- ricster
- Patrolman 1000+
- Posts: 5850
- Joined: 13 Jan 2010 11:16
- Full Name: Cedric Warner
- Nickname: Cedric
- Home Town: Alberton Gauteng
- Current 4x4: '99 Nissan Patrol 4.2 Turbo Diesel
- Home Language: English
- Location: LA..... No not Los Angles ..... Lower Alberton, Gauteng
- Has thanked: 591 times
- Been thanked: 468 times
Re: DIY DRAWER SYSTEM
Very very nice !!!.... I like the whole thought pattern on it !!
Regards
Cedric
Nissan Patrol GL 4.2 Diesel Turbo (Iron Maiden)
Nissan SANI 3.0 V6 4x4 (SOLD)
Isuzu KB 280 DT 2x4 ('ol Smokey) - SOLD
Suzuki TL 1000R "V twin" (Growler) - SOLD
Cedric
Nissan Patrol GL 4.2 Diesel Turbo (Iron Maiden)
Nissan SANI 3.0 V6 4x4 (SOLD)
Isuzu KB 280 DT 2x4 ('ol Smokey) - SOLD
Suzuki TL 1000R "V twin" (Growler) - SOLD
- Rhett
- Senior Member
- Posts: 482
- Joined: 26 Jan 2016 14:48
- Full Name: Rhett van der Stelt
- Nickname: Rhett
- Home Town: Heidelberg
- Current 4x4: 3.2Did Shorty Pajero
- Home Language: English
- Location: Heidelberg
- Has thanked: 163 times
- Been thanked: 75 times
Re: DIY DRAWER SYSTEM
Thanks guys..
Ja, I will have to test it out on a few trips and see how it performs. At this stage I'm 97% finished. Social and 4x4 life always gets in the way.
Ja, I will have to test it out on a few trips and see how it performs. At this stage I'm 97% finished. Social and 4x4 life always gets in the way.
Rhett
https://www.youtube.com/channel/UC9e98c ... XUyixKJavQ
Nissan Patrol 4.8 GRX
Toyota Land Cruiser HJ45
https://www.youtube.com/channel/UC9e98c ... XUyixKJavQ
Nissan Patrol 4.8 GRX
Toyota Land Cruiser HJ45
- David M
- Patrolman
- Posts: 794
- Joined: 12 Nov 2013 15:13
- Full Name: David Marais
- Nickname: David Marais
- Home Town: Midrand
- Current 4x4: 1998 4.5 GL Patrol
2006 4.2 Td Bakkie (SWAMBO's) - The "Firetruck" - Home Language: English
- Location: Midrand
- Has thanked: 20 times
- Been thanked: 96 times
Re: DIY DRAWER SYSTEM
I really like the way it is not over complicated.
One suggestion is to cut a trapdoor under the bottom drawer so that you do not need to remove the system if you need to get to the fuel pump.
One suggestion is to cut a trapdoor under the bottom drawer so that you do not need to remove the system if you need to get to the fuel pump.
There are still places out there!!!! - Daniel Goz - The "Tapam" movie
Who is online
Users browsing this forum: No registered users and 18 guests