Brake pedal feel different on first brake application
-
- Patrolman
- Posts: 609
- Joined: 01 Feb 2010 07:42
- Full Name: Andries
- Nickname: None
- Home Town: Pretoorsdorp
- Current 4x4: 4.8 GL with hairdryer.
- Home Language: Afrikaans
- Has thanked: 28 times
- Been thanked: 38 times
Re: Brake pedal feel different on first brake application
Differentiate between softer and longer travel? i.e. when you reach the firm pedal point on first attempt is it the same firmness as on the 2nd application
1) Does it happen only while you are driving
2) Does it happen while not moving with engine on?
3) Does it happen with engine off - and not moving? - Do press the brake a couple of time after switching off
from bottom
3) eliminated the vacuum booster , if travel changes from the first to the second the problem is most likely hydraulic, could be air in the system, leaking master you will generally be able to depress the pedal more and more by keeping pressure on the pedal
2) could be vacuum booster, first use adds the power but vacuum leaks or insufficient on second and feels like pedal travel less but actually the difference is the power assistance
1) could be that a disk is not running true, or caliper loose and while driving the caliper pistons are moved further away, thus on first brake application you need to take up the movement and have more pedal travel, however quick subsequent brake application the piston have not moved as much back and the travel is less
1) Does it happen only while you are driving
2) Does it happen while not moving with engine on?
3) Does it happen with engine off - and not moving? - Do press the brake a couple of time after switching off
from bottom
3) eliminated the vacuum booster , if travel changes from the first to the second the problem is most likely hydraulic, could be air in the system, leaking master you will generally be able to depress the pedal more and more by keeping pressure on the pedal
2) could be vacuum booster, first use adds the power but vacuum leaks or insufficient on second and feels like pedal travel less but actually the difference is the power assistance
1) could be that a disk is not running true, or caliper loose and while driving the caliper pistons are moved further away, thus on first brake application you need to take up the movement and have more pedal travel, however quick subsequent brake application the piston have not moved as much back and the travel is less
-
- Patrolman
- Posts: 641
- Joined: 07 Apr 2009 07:13
- Full Name: Malcolm van Coller
- Nickname: mvcoller
- Home Town: In most reverse order - Jhb, V-Town, Vryburg, CT
- Current 4x4: 2008 3.0 Di Patrol GL
and
1999 4.5 Patrol SGL - Home Language: Afr & Eng
- Location: Befordview
- Has thanked: 40 times
- Been thanked: 180 times
- Contact:
Re: Brake pedal feel different on first brake application
Start bleeding at the furtherest point from the reservoir and work your way to the closest. That is the correct order. Much easier way to remember the bleeding order!
-
- Senior Member
- Posts: 189
- Joined: 19 Nov 2013 11:10
- Full Name: Florian M.
- Nickname: Flo
- Home Town: Hoedspruit
- Current 4x4: '99 GRX 4500
- Home Language: German
- Has thanked: 41 times
- Been thanked: 33 times
Re: Brake pedal feel different on first brake application
Hi Andriess,
I‘ll try to work it out according to your hints.
What I can say already is that the reservoir is just a tad above max, so there shouldn‘t be any leak.
Thanks for the update regarding the bleed: I‘ll pass that through to my workshop.
I‘ll try to work it out according to your hints.
What I can say already is that the reservoir is just a tad above max, so there shouldn‘t be any leak.
Thanks for the update regarding the bleed: I‘ll pass that through to my workshop.
- iandvl
- Patrolman 1000+
- Posts: 1765
- Joined: 12 Jan 2015 13:26
- Full Name: Ian de Villiers
- Nickname: Ian
- Home Town: Garsfontein
- Current 4x4: Nissan Patrol 4.5 GRX
- Home Language: English
- Has thanked: 441 times
- Been thanked: 670 times
Re: Brake pedal feel different on first brake application
I checked the manual, and it is as I outlined in my earlier post.
1: Load sensing valve (LSV).
2: Back left.
3: Back right.
4: Front left.
5: Front right.
The LSV is not the furthest point from the reservoir.
Ian de Villiers
Patrol 4.5 GRX
Jurgens XT65 2x0 with Super Select Zero
ORRA: H80
Patrol 4.5 GRX
Jurgens XT65 2x0 with Super Select Zero
ORRA: H80
-
- Senior Member
- Posts: 189
- Joined: 19 Nov 2013 11:10
- Full Name: Florian M.
- Nickname: Flo
- Home Town: Hoedspruit
- Current 4x4: '99 GRX 4500
- Home Language: German
- Has thanked: 41 times
- Been thanked: 33 times
-
- Patrolman
- Posts: 609
- Joined: 01 Feb 2010 07:42
- Full Name: Andries
- Nickname: None
- Home Town: Pretoorsdorp
- Current 4x4: 4.8 GL with hairdryer.
- Home Language: Afrikaans
- Has thanked: 28 times
- Been thanked: 38 times
Re: Brake pedal feel different on first brake application
I'm always hesitant to bleed brakes on older cars, even more so if you don't know the history. The problem is that when bleeding you all of a sudden use a part of the master cylinder that would not have seen any use it a number of years and any deterioration of that surface could potentially damage your master cylinders seals causing problems.
This happened on a 20 year old car that might not have had it the brakes bled or fluid exchanged in 15 years if not more. when I opened the m/c you could see a shiny part , then dull , then shiny then dull( dual m/c) and i believe that when the bleeding was done the seals moved over the unused part causing damage.
Thus I prefer to bleed using vacuum at the caliper or pressurizing the system from the reservoir side and if manual bleeding is required to put a spacer / block under the brake pedal as not to push it to the floor.
I'll gladly hear your opinions on it.
This happened on a 20 year old car that might not have had it the brakes bled or fluid exchanged in 15 years if not more. when I opened the m/c you could see a shiny part , then dull , then shiny then dull( dual m/c) and i believe that when the bleeding was done the seals moved over the unused part causing damage.
Thus I prefer to bleed using vacuum at the caliper or pressurizing the system from the reservoir side and if manual bleeding is required to put a spacer / block under the brake pedal as not to push it to the floor.
I'll gladly hear your opinions on it.
- SCUBA Patrol
- Senior Member
- Posts: 412
- Joined: 08 Apr 2009 11:15
- Full Name: Phillip Jacobs
- Nickname: Phillip
- Home Town: Cape Town (Stellenbosch)
- Current 4x4: Patrol 2006 3l diesel(die eerste Voetspore een)
- Home Language: Afrikaans
- Location: Cape Town, Stellenbosch (Paradyskloof)
- Has thanked: 31 times
- Been thanked: 32 times
Re: Brake pedal feel different on first brake application
Makes sense Andries, seeing that hidrolic fluid is hygroscpoic, it absorbes water, and thus the rust effect on break parts.
Phillip
2006 3l with MADMAN
2006 3l with MADMAN
-
- Senior Member
- Posts: 189
- Joined: 19 Nov 2013 11:10
- Full Name: Florian M.
- Nickname: Flo
- Home Town: Hoedspruit
- Current 4x4: '99 GRX 4500
- Home Language: German
- Has thanked: 41 times
- Been thanked: 33 times
Re: Brake pedal feel different on first brake application
That‘s an interesting point!
I think -but have to ask to be sure- that the car got fresh brake fluid 1 or 2 years ago.
I just tested after driving with engine off: on first press I could depress the pedal with little force to lets say 30% of travel.
The second pressing was much firmer and I had much less travel, the 3rd try even gave a tad less way I think.
Maybe I should have the discs checked for alignment?
I think -but have to ask to be sure- that the car got fresh brake fluid 1 or 2 years ago.
I just tested after driving with engine off: on first press I could depress the pedal with little force to lets say 30% of travel.
The second pressing was much firmer and I had much less travel, the 3rd try even gave a tad less way I think.
Maybe I should have the discs checked for alignment?
-
- Patrolman
- Posts: 609
- Joined: 01 Feb 2010 07:42
- Full Name: Andries
- Nickname: None
- Home Town: Pretoorsdorp
- Current 4x4: 4.8 GL with hairdryer.
- Home Language: Afrikaans
- Has thanked: 28 times
- Been thanked: 38 times
Re: Brake pedal feel different on first brake application
On your first press the booster still had vacuum and you typical feel that you required less force and the travel was a bit more. Your second and third should be the same.
I suggest before you start it tomorrow morning you check the difference in travel between your first three presses,( do them 2 seconds apart) there should be no noticeable difference, if the pedal comes up - I.e 2, 3 and 4 is now firmer/ higher then you could have air in the system.
After this keep your foot on the brake and start the car, you should feel the brake pedal being pulled in by the brake booster, sign that booster is working but not indication if it's leaking vacuum or not
I suggest before you start it tomorrow morning you check the difference in travel between your first three presses,( do them 2 seconds apart) there should be no noticeable difference, if the pedal comes up - I.e 2, 3 and 4 is now firmer/ higher then you could have air in the system.
After this keep your foot on the brake and start the car, you should feel the brake pedal being pulled in by the brake booster, sign that booster is working but not indication if it's leaking vacuum or not
- Peter Connan
- Moderator
- Posts: 6018
- Joined: 10 Sep 2010 07:21
- Full Name: Peter Connan
- Nickname: Piet
- Home Town: Kempton Park
- Current 4x4: 1996 Patrol 4.5SGL
- Home Language: Afrikaans
- Location: Kempton Park
- Has thanked: 1069 times
- Been thanked: 982 times
Re: Brake pedal feel different on first brake application
But not too hard a pressure. I have burst two brake lines by doing this!
Mag ons ons kenniskry met lekkerkry aanhoukry.
Who is online
Users browsing this forum: No registered users and 23 guests